Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterTrusted Chimney Cap & Crown for Camden Homeowners
A Camden Chimney Cap & Crown repair typically costs between $180 for a basic cap installation and $1,200 for full crown rebuilds, with most jobs completed in a single visit. Level Two Chimney Co. has inspected and serviced more than 38,000 chimneys since 2009, and we’ve documented the specific damage patterns that Camden’s freeze-thaw cycles and coastal moisture produce on chimney tops. Call us at (856) 741-9572 for a written estimate before any work begins.
We’ve worked on cap and crown issues across Camden’s housing stock, from the brick twins in Cramer Hill to the older masonry in Parkside and the postwar homes near Whitman Park. The problem is almost always the same: water gets in, freezes, expands, and turns a small crack into spalling brick, a rusted flue liner, or a leak that shows up as a stain on your ceiling. Our home page explains our full inspection approach, but on this page we’re focused specifically on what sits on top of your chimney and what it costs to fix it right.
Every cap and crown job we do starts with an NFPA 211 Level 2 camera inspection so we can show you exactly what the top of your flue looks like. We don’t guess, and we don’t sell you a cap because it sounds like a good idea. We document the condition, give you a written price with a written scope, and back it with our 365-Day Done Right Promise. That’s Haven Standard Clause 1: have it in writing before anyone starts.
What Our Chimney Cap & Crown Service Includes
Cap Installation
Cap installation is the placement of a protective cover over a single flue or flue termination to block rain, animals, and debris while allowing smoke and gases to exit. In Camden, we install caps on chimneys that have never had one, particularly common in homes built before 1980 where the original builder left the flue open to the weather. We measure your flue precisely, source the cap through our Haven buying network from manufacturers like Famco or Copperfield, and secure it with stainless steel fasteners that won’t rust out in Camden’s humid summers.
Cap Replacement
Cap replacement removes a damaged, incorrectly sized, or rusted cap and installs a new unit matched to your flue type and fuel source. We replace a lot of caps in Camden that were installed by roofers or handymen using galvanized steel or the wrong size, which lets water run down the flue wall anyway. When we replace your cap, we include a camera inspection of the flue interior to confirm the old cap didn’t let moisture damage the liner or smoke shelf, and we give you photos of both the old condition and the new installation.
Crown Repair
Crown repair addresses cracks, deterioration, or improper slope in the concrete slab that sits between your brick courses and the flue termination. In Camden’s climate, crown concrete absorbs rain, freezes overnight from November through March, and spalls off in chunks that expose the brick below to accelerated damage. We repair crowns by cutting back deteriorated concrete, installing proper expansion joints around the flue tile, and pouring new high-strength concrete with a minimum 2-inch overhang and positive slope away from the flue.
Crown Coating
Crown coating is the application of a flexible, waterproof membrane over a structurally sound crown that has minor cracking or surface porosity. This is not a fix for a crown that’s already separating from the brick or showing deep fractures, but it’s an effective intermediate step for Camden homeowners whose crowns are starting to show hairline cracks after 15-20 years. We use HeatShield CrownCoat or equivalent elastomeric products that remain flexible through freeze-thaw cycles, and we photograph the crown before and after so you can see the coverage and thickness.
Multi-Flue Cap
Multi-flue caps cover two or more flue terminations with a single hooded structure, which is necessary when your chimney has multiple fireplaces, a fireplace and a furnace, or a fireplace and a water heater venting through the same structure. These are common in Camden’s larger twins and rowhomes where one chimney serves multiple appliances. We measure the total footprint, calculate proper clearances to combustibles, and install a cap with screened sides that keeps animals out without restricting draft for any of the connected appliances.
Custom Cap
Custom cap fabrication is required when standard sizes won’t fit an oversize flue, an unusual chimney pot, or a historic masonry termination that needs to be preserved. We’ve built custom caps for Camden properties in Cooper Grant and the historic districts where the original architectural details matter. We work with Copperfield and local sheet metal shops to produce stainless steel or copper caps that match the dimensions exactly, and we always provide a drawing for approval before fabrication begins.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Chimney Cap & Crown
We’ve installed and serviced hundreds of Famco caps across Camden and Gloucester City, and we stock their standard galvanized and stainless steel models in our warehouse. Famco’s multi-flue units are particularly reliable for the shared chimneys common in Camden’s rowhouse stock, and their mesh sizing meets code for keeping out squirrels and raccoons without clogging with creosote.
We also work extensively with Copperfield’s custom fabrication line for historic properties and unusual flue configurations, and we source DuraFlex liner components when crown damage has exposed a deteriorated flue that needs relining before it can be properly capped. Whether you have a Famco, Copperfield, DuraFlex, or any other make already on your chimney, we can service it, replace it, or upgrade it with a documented photo record of the condition we found and what we did about it.
Before
AfterSigns You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling near your fireplace. This almost always means water is entering through a failed crown, missing cap, or deteriorated mortar at the chimney top. In Camden, we see this most often after the first hard freeze of winter, when water that seeped into cracks expands and opens a path straight to your interior.
- Chunks of concrete or mortar on the roof or ground near the chimney. Spalling crown material is not a cosmetic issue. Once the crown loses its overhang and slope, water runs directly down the brick faces, accelerates mortar joint deterioration, and can lead to partial chimney collapse that costs thousands to rebuild.
- Rust stains on the exterior brick or at the damper. Rust means moisture is reaching metal components that should stay dry. A properly installed cap and intact crown keep the flue liner, damper, and firebox metal dry. Rust at the damper often indicates years of water entry that a simple cap installation won’t fully solve.
- Bird or animal sounds from the chimney. Squirrels, raccoons, and starlings enter uncapped flues readily, and Camden’s mature tree canopy in neighborhoods like Collingswood and Haddonfield provides easy access. Animals build nests that block draft, introduce parasites, and can ignite if they fall into a burning fireplace.
- White efflorescence on exterior brick. That chalky white deposit is mineral salts left behind when water moves through the masonry and evaporates. It means your crown or cap is allowing sustained water entry, and it’s often the first visible sign that the interior flue liner is being compromised by the same moisture.
Our Chimney Cap & Crown Process - Step by Step
- 1
Schedule and confirm. When you call (856) 741-9572, a live person answers 24 hours a day. We book your appointment, assign a named technician, and text you when they’re en route with an estimated arrival window. You’ll know who’s coming and when.
- 2
NFPA 211 Level 2 inspection with camera. Before we discuss caps or crowns, we run a camera down your flue to document liner condition, creosote buildup, and any water damage patterns. We also photograph the exterior crown and cap from the roof or with a pole camera. This is Haven Standard Clause 4: a documented photo record on every visit, which we’ve done on every job since 2009.
- 3
Written diagnosis and price. We show you the photos, explain what we found in plain terms, and deliver a written scope with a written price before any work begins. If your crown is repairable with coating, we’ll say so. If it needs full rebuild, we’ll show you why. No surprises, no pressure.
- 4
Cap or crown work with documented completion. Our technicians install or repair using materials sourced through our Haven buying network. For crown work, we use proper concrete mixes with air entrainment for freeze-thaw resistance, not bagged mortar mix that will crack again in two winters. We photograph the completed work from multiple angles.
- 5
Written warranty and archive record. You receive a written warranty backed by our 365-Day Done Right Promise, and your photo record is archived in our system for future reference. If you sell your home or need to document condition for your insurer, the record exists and is accessible.
How Much Does Chimney Cap & Crown Cost in Camden?
A standard single-flue cap installation in Camden typically runs $180-$340, including the cap, fasteners, and basic flue inspection. See our full Chimney Cap & Crown cost guide for more pricing details. Crown coating for a sound crown with minor cracking is usually $400-$650. Partial crown repair, where we cut back and repour sections, ranges from $650-$950. Full crown removal and rebuild on a typical Camden rowhouse chimney runs $900-$1,200, and multi-flue cap systems for shared chimneys generally fall between $450-$780 depending on size and access.
Several factors move these prices. Roof pitch and height affect labor time and safety equipment needs. A two-story home in Collingswood with a steep roof costs more than a single-story ranch in Gloucester City with walkable access. The extent of hidden damage also matters. We’ve opened crowns that looked merely cracked and found the flue liner below deteriorated from years of water entry, which requires relining before a new cap or crown will do any good. We always find this with the camera first, show you, and price it separately so you understand exactly what you’re paying for.
To avoid overpaying, get any estimate in writing with a specific scope. A “chimney cap special” that doesn’t include inspection of the flue below is selling you metal, not solving your problem. Our estimates are free, detailed, and include no obligation. If you have a written estimate from another company, we’ll give you a free second opinion under Haven Standard Clause 2.
Chimney Cap & Crown Near Camden - Our Service Area
We serve Camden directly and the surrounding communities where our technicians live and work: Chimney Cap & Crown in Collingswood, Chimney Cap & Crown in Gloucester City, Audubon, Mount Ephraim, Haddon Heights, Haddonfield, Bellmawr, Philadelphia, Barrington, Palmyra, and Ashland. Most appointments are scheduled within a few business days, and we carry common cap sizes and crown repair materials on our trucks so we can often complete the work in a single visit once you’ve approved the written price.
Serving Camden, NJ - Our Local Coverage Area
We’re based in the Camden area and know this community well, including nearby Collingswood Chimney Cap & Crown projects. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Chimney Cap & Crown in Camden
Chimney cap and crown service protects the top of your chimney from water, animals, and debris entry. The cap is a metal cover over the flue opening; the crown is the concrete slab that sheds water away from the flue and brick structure below. Together they form your chimney’s first defense against the moisture damage that destroys liners, rusts dampers, and rots adjacent framing. Call (856) 741-9572 for a free estimate on your cap or crown condition.
Most cap installations and replacements take 1-2 hours. Crown coating takes 2-3 hours including surface prep and cure time. Full crown rebuilds typically require 4-6 hours and may need a return visit if weather interferes with concrete curing. We always give you a time estimate in writing with your price, and we don’t charge extra if a job runs longer than expected. Call (856) 741-9572 to schedule.
Standard cap installation runs $180-$340, crown coating $400-$650, partial crown repair $650-$950, and full crown rebuild $900-$1,200 in the Camden market. Multi-flue caps range $450-$780. Your specific price depends on roof access, flue size, and whether hidden damage requires additional work. We deliver a written price before any work starts, and estimates are free. Call (856) 741-9572 for your exact quote.
Yes, we install, repair, and replace Famco and Copperfield caps regularly, and we stock common Famco sizes for same-visit replacement when possible. We also work with DuraFlex and HeatShield products for integrated cap and liner systems. If you have a different brand or don’t know what brand you have, we can identify it during inspection and match or upgrade it appropriately. Call (856) 741-9572 to schedule.
We answer calls live 24 hours a day, 7 days a week, and we prioritize active water infiltration or animal entry that poses immediate fire or health risks. True emergencies, such as a crown collapse or cap blow-off during a storm, get scheduled as quickly as possible. For non-urgent issues, we typically book within a few business days. Call (856) 741-9572 to discuss your situation.
Every job is backed by our 365-Day Done Right Promise: if it’s not done right, we make it right. Cap installations carry a manufacturer warranty on materials plus our workmanship guarantee. Crown repairs and rebuilds include a written warranty against material and installation defects. All warranties are documented in writing before work begins under Haven Standard Clause 1. Call (856) 741-9572 for details.
Clear a path to your fireplace and move any furniture or valuables 6 feet away from the work area. Ensure we have access to your roof or yard if exterior work is planned, and secure pets in a separate room. You don’t need to clean the fireplace or do any pre-inspection work yourself. We’ll cover floors, use drop cloths, and leave the work area clean. Call (856) 741-9572 to book your appointment.
Schedule Your Chimney Cap & Crown Service in Camden Today
Call (856) 741-9572 to speak with a live person 24 hours a day, or request your free estimate online. We’ll assign a named technician, send a text when they’re on the way, and deliver a written price with a written scope before any work begins. Every job includes an NFPA 211 Level 2 camera inspection, a documented photo record, and our 365-Day Done Right Promise. No obligation, no pressure, no surprises.
Written by Corrine Halstead, Owner at Level Two Chimney Co., serving Camden since 2009.